Drip edge
Bent or missing drip edge is replaced at eaves and rakes with the underlayment lapped correctly.
Roof Repair
Flashing Repair Hawthorne, NJ
Most leaks at walls, dormers and roof edges in Hawthorne come down to flashing, and a roofer can fix it by replacing the failed metal rather than caulking over it, with the wall sheathing checked for hidden rot. One call to (862) 434-1182 reaches a nearby roofer who repairs flashing.
Wherever a roof meets a wall, a dormer, a skylight, a valley or an edge, it relies on flashing to keep water out. Along a sidewall, individual step flashing pieces interleave with every course of shingles, counter flashing covers their tops, and a kickout diverter at the lower end turns water away from the siding. When any piece is missing, loose or rusted through, water gets behind the roof covering.
Flashing leaks are sneaky because the water often runs into the wall instead of the attic. Without a kickout, roof runoff dumps against the siding where the wall meets the eave, soaking the sheathing and framing below it. Catching it early keeps the repair to the flashing instead of the wall.
A bead of sealant along a joint is a warning sign, not a repair. Sealant can hold for a while, but it fails sooner or later, and the joint leaks once more. Lasting flashing repair means new metal installed in the right order, with sealant only as a backup.
Flashing Repair is often paired with chimney flashing repair and roof leak repair, depending on the cause.
Need flashing repair in Hawthorne? Call (862) 434-1182 to talk to a local roofer.
Call nowThe process
How flashing repair works
Here is how a roofer typically approaches a flashing repair.
Inspect the joint
The roofer checks the joint from the roof and the attic, looking for missing pieces, rust, face nails and caulk hiding a gap. Soft siding or stained trim below the joint suggests the wall needs a look too.
Open the joint
The shingles next to the wall come up, and the lowest siding courses come off to expose the flashing. Working the new pieces in correctly depends on access behind the siding.
Install new flashing
Fresh step flashing goes in course by course with the shingles, starting with a kickout at the eave. Each piece is nailed through the roof side only, so the wall and roof can move independently.
Add counter flashing
On masonry walls, counter flashing is set into a cut joint; on framed walls, the housewrap and siding cover the flashing. Siding pressed tight to the shingles stays wet and rots.
Check drip edge
Drip edge along eaves and rakes is checked and replaced where it is bent or missing, lapped correctly with the underlayment. At eaves the underlayment goes over the drip edge; at rakes the drip edge goes over it.
What is included
Flashing a roofer can repair
Kickout flashing
Missing kickout diverters are installed at the base of sidewalls which protects the wall below.
Apron flashing
Headwall metal at the top of a slope is replaced so water cannot run behind it.
Step flashing
Sidewall flashing is rebuilt one course at a time behind the housewrap.
Cap flashing
Loose counter flashing is secured so the top edge of the step flashing stays covered.
Related service
Roof Flashing Repair Hawthorne, NJ
Roof flashing repair ranges from resetting a single loose piece to rebuilding a full sidewall. Minor work includes refastening loose metal or adding a missing kickout; bigger jobs mean pulling siding and replacing every step piece along a wall. Ask the roofer which kind of repair your joint needs.
Not every flashing metal works in every spot. Copper outlasts most roofs, galvanized steel is durable and aluminum is light and easy to bend, though it corrodes in contact with wet masonry. Mixing copper with aluminum or galvanized metal in contact can cause corrosion, so the roofer matches the metal to what is already there.
Related service
Roof Valley Flashing Hawthorne, NJ
Roof valleys carry the runoff from two slopes, so they handle more water than any other part of the roof. In an open valley, a band of metal stays exposed down the center, while in a closed or woven valley the shingles cover the valley and the underlayment beneath does the heavy lifting. Both need ice and water shield underneath, centered in the valley.
Common valley problems include rusted metal, debris dams, worn shingles and nails placed too close to the centerline. Small installation details, like clipping the upper corners of the cut shingles, keep water flowing down the valley instead of across it. Fixing a valley usually involves stripping it, relining it and installing new metal or reshingling.
Local help
Flashing Repair Near Me
In Hawthorne, many flashing problems date back to an old reroof where the original flashing was reused or caulked instead of replaced. From Hawthorne out to neighboring towns such as Glen Rock, Haledon, Fair Lawn and Midland Park, older homes often have rusted or face-nailed flashing, while newer ones sometimes lack kickouts entirely, and each of those joints is a place worth checking.
Searching for flashing repair near me from Hawthorne or Glen Rock, Haledon, Fair Lawn and Midland Park? Call (862) 434-1182 to talk to a roofer who works in your part of town.
How the weather here affects roofs around Hawthorne
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. Most homeowners in Hawthorne, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why act early
Drier ceilings
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Roofers who know Hawthorne
Local roofers see the same roofs and storm damage across Hawthorne and nearby towns.
Clear next steps
Ask the roofer about the cause, the options and the estimate before work starts.
Flashing Repair FAQ
What are the signs of bad roof flashing?
Water showing up near a wall joint, skylight or valley points to flashing. Outside, look for rust, gaps, lifted metal, nails through the face and heavy caulk along the joint. Stained trim where a roof edge meets a wall is a common clue too. Call (862) 434-1182 to reach a roofer.
Why does my roof need kickout flashing?
A kickout is a small diverter at the bottom of a roof-to-wall joint, where the roof edge ends against a wall. It turns water that runs down the step flashing outward into the gutter instead of letting it pour behind the siding. Without one, the wall below that joint often rots quietly for years.
Is it possible to fix flashing without a new roof?
Flashing is repaired on existing roofs all the time. The roofer removes the shingles and siding along the joint, installs new flashing and reshingles that strip. For a worn-out roof, combining the work with a replacement avoids doing the joint twice.
What is step flashing and why does it matter?
Step flashing is a series of small L-shaped pieces, one for each course of shingles along a wall. Because each piece laps the one below, water is passed down the wall joint from piece to piece and onto the roof. A long single strip sends water under the roofing, which is why step pieces are the standard.
Will caulk fix leaking flashing?
Sealant is a short-term patch for flashing, not a lasting repair. Sun and temperature swings crack it, and water gets behind it again, sometimes trapped where it rots wood faster. Real repairs use new metal lapped in the right order.
More questions? Call (862) 434-1182
Other services that may help
Chimney Flashing Repair
Chimney flashing rebuilt so the roof-to-brick joint sheds water again, with a cricket added where the chimney is wide.
Learn moreRoof Leak Repair
Stopping water at the pipe boots, flashing, valleys and nail holes where roofs actually leak, before wet decking and insulation turn into rot.
Learn moreSkylight Repair
Skylight repair from the flashing on the roof to the glass and the frame, so the opening stays dry through every storm.
Learn moreRoof Vent Repair
Fixing the vents and pipe collars that poke through a roof and often leak first, before a small crack soaks the attic.
Learn more
Looking for something else?
See all roofing servicesNeed flashing repair in Hawthorne, NJ?
Call now for Hawthorne flashing repair and help in the towns around it.